Broken Strat whammy bar

Can't believe it was May since my last post!  I've been so entrenched with basement renos (to include a new workshop ...eventually...) and summer fun that my guitar projects have taken a back seat.  Thankfully my clients haven't had any emergencies!

Until now...

This part of the Strat tremolo is often overlooked during the preparation process.  These threads need to be lubricated and cleaned quite often, as the beep hole in the trem block is the perfect place for grime to hide.

Many players use a graphite lubricant for many areas of the guitar, but for this particular spot I recommend just a drop of clear mineral oil on the bottom few threads.  Graphite lube in this area will only accumulate more grime over time.

With this guitar, the bar has broken off rather deep ~ below the surface of the trem block if it were to be removed.  In cases where they break off flush or slightly below the saddle plate, removal of the trem block would allow you to unscrew the broken piece by hand as it would be exposed above it's surface ~ no drilling required.

Despite centre punching the piece, these extractions can often go awry due to the uneven surface created from the break.  After a visit to the drill press, the hole meandered off centre but I caught it on time before it damaged the threads of the trem block.  Just enough of a hole to use the extractor bit to remove the piece.

I noticed the piece was quite short, meaning not a lot of thread was turning in to the trem block.  When I attempted to install a new arm, the threads were very stiff and it was obvious they needed a good cleaning.

A liberal amount of mineral oil on the threads of the new arm, and working it back & forth in the threads began to work the grime lose.  The threads were so tight with buildup that the arm could only be threaded in half way before it was tight, which explains why the old arm broke off so short.

Each time the new arm was threaded in tightly, it was removed, cleaned, re-lubricated and threaded in again going further every turn.  

It didn't take long to feel the results ~ the new trem arm threaded in all the way down with the appropriate amount of tension.

Guild GAD-50 ~ saddle repair

I've always loved the adjectives people choose to describe the sound of an instrument.  How does something sound bright, dark, brown, flappy, muddy, jingly, raspy, layered, twangy, or rootsy, etc.?  I'm not exactly sure, but we all seem to know it when we hear it.

This guitar has lots of "Schraang!"

I'm always sceptical of off-sohore made instruments, but there's always the exception which is where this one sits.  Bang for buck, the quality of these guitars is outstanding.




The owner of this guitar regularly puts it through it's paces.  The concern here was that the high B and E string had become quieter in the EQ when plugged in, in addition to the high E buzzing with a "sitar" effect.  Inspecting the saddle soon showed where the problem was.  When the pickup system was installed, there were no grooves cut in the new bone saddle to house the strings.  Subsequently, the owner regularly lubricated the saddle with graphite in an attempt to alleviate some audible buzzing and/or intonation issues.

Over time, the lubricant worked it's way on to the b-band pickup under the saddle and congealed itself between the saddle and pickup surface, causing a muted response when plugged in.

Once this gunk was cleaned off down to the original surface, the saddle itself was addressed.  Appropriately wide and deep slots were cut to accommodate the strings, the intonation was set by sculpting the saddle in place.  No more graphite lube required!

1990 Hamer Centaura ~ Life Support ++

Amid many other ongoing projects, this is one that I've been chipping away at bit by bit. Fortunately, the owner has given me lots of time, but knowing he's waiting so patiently I thought it would be time for an update! I'll refresh this post with it's progress in due time...

These are excellent, US made guitars and it's obvious the owner has certainly poured some mojo into this particular one. The finish was removed to reveal the solid Mahogany body, and the stock pickups have been replaced with a Seymour Duncan JB in the bridge and two vintage Strat style singles in the middle and neck.










Sanding the finish resulted in making the area by the switch plate quite thin and frail.  This will need some reinforcement that will involve some custom work.

The initial concern with this guitar was the wiring that was done when the pickups were replaced. While it did work, it wasn't to the standard that the owner would like.  There is also a component missing that I believe may have been a toggle switch for coil splitting.  Endless options are available to put in that opening, so we'll see what the owner decides...

You can see some left-over red sparkle paint under the control cover, which was misplaced over the years.  No problem to cut a new one to shape, but the concern now is that the sanding of the body has resulted in a very shallow recess that is not deep enough for the cover to sit flush.  This will be routed down to accommodate the new cover.







This Schaller-made licensed Floyd Rose is in need of a thorough cleaning, as with the rest of the components.  This guitar has been dismantled completely for this project so as to breathe new life into it and get it back in to service!

You can see the string spacing on the humbucker is narrower than the bridge.  This pickup is for a Gibson style scale.  For this type of bridge, a Trembucker is required ~ same pickup but with wider string spacing. Fortunately I have one in stock!

Piece by piece, the tremolo was overhauled and thoroughly cleaned and threads lubricated.  I make sure to keep the same saddle graphite clamp blocks (the small cubes) in their original location, as the wound strings tend to make an indent over time.  If they were to be mixed up, it's quite possible to be faced with a "sitar" effect buzzing away in an unwound string.

No explanation for this, other than an obvious shortage of shrink tube!  This pickup can easily be repaired with a little time and solder, not to mention a good cleaning.

Still lots of playing left in these frets.  Once they're dressed and these inconsistencies are removed, it will feel like new!








A common occurrence on well played guitars ~ individual string indents in the first 3-5 frets and then flat crowns in the upper register where string bending is done.  These jumbo frets are still tall enough to benefit from dressing.




This fretboard is begging for oil.  Buildup of grime will suck a lot of the natural oils out of the wood, making it more susceptible to wear.  A cleaning and light coat of lemon oil when changing strings will not only prolong the life of the fretboard, but it will also be a pleasure to play.







Stay tuned!